Distribution Boards & Consumer UnitsMCB (Miniature Circuit Breakers)RCCB (Residual Current Circuit Breakers)

Single-phase or three-phase DB: a checklist for homes and shoplots

How to tell which supply you need, and what to ask for when you buy a distribution board.

2 min read5 steps

Ask us a question

01Single phase or three phase

Single phase has one live wire and a neutral, 240V. Three phase has three live wires and a neutral, and is the supply for bigger loads and three-phase machines. TNB's application guide covers single-phase supply for demand up to about 12 kVA, and three-phase above that. Homes with many air-conditioners, a large house, or a shoplot with machines often need three phase. TNB and your electrician confirm which one you get.

EPS (Utama Switchgear) EL Series Distribution Board (L Size), 2 to 6 Rows
Key point

Most homes run on single phase. TNB gives single phase for demand up to about 12 kVA.

02Count the ways

A way is one slot for a breaker. List your circuits: lights, sockets, water heater, each air-conditioner, kitchen, pump. Add them up, then leave a few spare ways for later. A board that is full on day one is a problem later. On a three-phase board, share the circuits across the three phases so no one phase is overloaded.

EPS (Utama Switchgear) JMS MCB 6kA Miniature Circuit Breaker, 1P, 2P, 3P, 4P
Key point

Many air-conditioners, a big water heater or three-phase machines push you towards three phase.

03Protection to ask for

A main switch to cut everything. An RCCB for earth leakage, and an RCBO or MCB for each circuit. The breaking capacity in kA must suit the supply, so ask your electrician which rating they need. Surge protection (SPD) is worth fitting where lightning storms are common. If you use two RCCBs one after the other, ask about a time-delay type for the upstream one.

EPS (Utama Switchgear) NGPL Residual Current Circuit Breaker (RCCB), 2P and 4P, 16 A to 100 A
Key point

Count the ways you need, then add a few spare ways.

04Choosing the board

Pick metal clad or plastic as the site needs, and the number of ways first. Check the enclosure's protection rating, so a board in a car porch or a shoplot back area is not exposed. Look for clear labels and enough space for the cables to bend. Ask us about EPS, Hager, Himel and other boards we list, and we will match the way count to your list.

EPS (Utama Switchgear) EM Series Metal Clad Enclosure (M Size), 2 to 5 Rows
Key point

Ask for the kA rating, the RCCB and surge protection. Confirm the supply with TNB and your electrician.

05Final checks

Label every circuit. Make sure the earthing is done and tested. Keep the cable sizes matched to the breakers. Leave the door of the board clear, not blocked by shelves. A registered electrician must install and test the board, and TNB handles the meter side. Bring or send your circuit list on WhatsApp and we will suggest the board.

EPS (Utama Switchgear) HSA3 MCB 10kA Miniature Circuit Breaker, 1P, 2P, 3P, 4P

This guide is general advice. Fixed wiring and distribution board work should be done by a qualified electrician.

From this range

See all Distribution Boards & Consumer Units

Next guides

Come to the counter

D-One Electrical is in Taman Bukit Indah, Iskandar Puteri, minutes from the Second Link. Bring the model number or a photo and we'll find it.

No. 11, 11A & 11B, Jalan Indah 15/2, Taman Bukit Indah, Iskandar PuteriMon to Fri 8am to 5pm, Sat 8am to 4pm. Closed Sundays and public holidays.

Prices change with stock and quantity, so we quote on request.

WhatsApp for a quote